NetBurner 3.5.8
PDF Version
MODRT1171 Hardware Design Guide

For Carrier Board Designers and System Integrators

NetBurner MODRT1171-100IR | Schematic Rev

1.6 | Preliminary



Module Overview

The MODRT1171 is a complete System on Module (SoM) based on the NXP i.MX RT1171 processor running at 800MHz. It provides dual 1 Gbps Ethernet, extensive I/O, and industrial temperature range operation in a compact 2.95" x 2.00" form factor.

Key Specifications

Parameter Value
Processor NXP i.MX RT1171, 800MHz ARM Cortex-M7
SRAM 2MB internal (TCM + OCRAM)
SDRAM 64MB (2x W9825G6KH-5, 32-bit bus)
Flash 128MB SPI NAND (W25N01GVZEIG) + 8Mbit Boot (GD25Q80CEIGR)
Ethernet 2x 1 Gbps via on-board KSZ9893 switch + optional 10/100 on headers
Operating Temp -40C to +85C
Dimensions 2.95" x 2.00" (74.9mm x 51mm)
Weight 1 oz (28 grams)
Mounting 1x 0.125" (3.18mm) dia hole
Headers 2x 50-pin, 0.1" (2.54mm) dual-row (S2011E-25-ND)

Block Diagram

+------------------+
| SDRAM |
| 2x W9825G6KH-5 |
| 64MB 32-bit |
+--------+---------+
|
+----------+ +------------+-------------+ +----------+
|Boot Flash| | | | I/O |
|GD25Q80C +--->+ NXP i.MX RT1171 +--->+ Headers |
|8Mbit | | 800MHz Cortex-M7 | | P1 + P2 |
+----------+ | | | 100 pins |
| 2MB SRAM | +----------+
+----------+ | |
|App Flash | +---+------+-------+--------+
|W25N01G +--->+ | | | |
|128MB | | RGMII USB1 USB2 DAC_OUT
+----------+ | | | | |
| v v v v
+---+---+---+ P2 P2 P2
| KSZ9893 | 14-16 17-19 9
| Eth Switch|
+--+-----+--+
| |
RJ-45 RJ-45
ENET0 ENET1

Note – Upcoming Rev 1.6 pinout change: The MODRT1171 currently ships as Rev 1.5, which this document describes. Rev 1.6 (estimated release December 2026) re-routes the SPI (LPSPI5), I2C (LPI2C6), and CAN (FlexCAN1) signals from the P1 header to the P2 header to make the module a drop-in replacement for the MOD5441X. The processor balls, peripheral instances, and driver APIs are unchanged – application software written for Rev 1.5 runs unchanged on Rev 1.6; only the connector pin locations move. The Rev 1.6 assignments are proposed and not yet finalized; confirm the final pinout with NetBurner before committing a board layout. See MODRT1171 Pinout Update at https://www.netburner.com/download/MODRT1171_Rev1p5_to_Rev1p6_Pinout_Update/ for the pin-by-pin mapping.


Power Supply Design

Main 3.3V Supply

The module requires a single 3.3VDC supply on pins P1-48, P2-2, and P2-50. All internal voltage regulators derive from this rail.

Configuration Current (3.3V)
No Ethernet connections 410 mA
1x Ethernet 100 Mbps 457 mA
2x Ethernet 100 Mbps 520 mA
1x Ethernet 1 Gbps 520 mA
2x Ethernet 1 Gbps 790 mA

Design Recommendations:

  • Use a regulator capable of at least 1A continuous output at 3.3V
  • 3.3V supply must reach operating voltage at a minimum rise rate of 2.4V/ms
  • Place bulk capacitance (47-100uF) near the module power pins
  • Add 0.1uF ceramic decoupling within 5mm of each Vcc pin
  • Ensure low-impedance ground connections between carrier and module

Internal Power Domains

The module generates all internal rails from the 3.3V supply. These are NOT available on headers and should NOT be externally supplied:

Domain Voltage Purpose
VDD_SOC_IN 1.0V CPU core logic
VDD_1V8 1.8V Internal logic
VDD_ENET_IO 1.8V Ethernet I/O
VDDA_3V 3.3V Analog supply
ADC_1V8_IN 1.8V ADC power domain
ADC_VREFH 1.65V ADC reference (TLVH431AIL5T)

SNVS Voltage Input (Vstby) – REQUIRED

Pin P1-3 (VDD_SNVS_IN) powers the Secure Non-Volatile Storage (SNVS) module, which controls:

  • Power-on-reset (POR) logic
  • Real-time clock (RTC) retention
  • Tamper detection circuitry
  • Secure key storage (SNVS GPR registers)

This pin must always be connected. Leaving it unconnected will cause unpredictable boot behavior.

Option A – No battery backup (typical): Tie P1-3 directly to the 3.3V supply (short to P1-48 / P2-2 / P2-50). SNVS powers up simultaneously with the main supply. RTC state is lost when power is removed.

Option B – Battery backup (coin cell): Connect a coin cell (e.g., CR2032) to P1-3 for RTC and secure key retention during power loss. The coin cell must be connected before any other supply is switched on.

Power Sequencing (per NXP i.MX RT1170 PMU requirements):

Power Up:

  • VDD_SNVS_IN must be turned on before any other supply, or be shorted to the 3.3V supply so they rise together
  • If a coin cell powers VDD_SNVS_IN, it must be connected before any other supply is switched on
  • When internal DCDC is enabled, an external delay circuit is required to delay DCDC_PSWITCH at least 1ms after DCDC_IN is stable (handled on-module)
  • POR_B must be held low during the entire power-up sequence (handled by on-module reset IC)

Power Down:

  • VDD_SNVS_IN must be turned off after all other supplies, or remain connected (coin cell) to retain RTC/security state

USB VBUS (5V)

Pin Signal Direction Notes
P2-14 USB1_VBUS_5V Input/Output USB OTG1 bus power
P2-19 USB2_VBUS_5V Input/Output USB OTG2 bus power
  • In host mode: The carrier board must supply 5V (min 500mA per port) to these pins
  • In device mode: These pins sense VBUS from an upstream host
  • Add a current-limiting switch (e.g., TPS2051) for host mode operation
  • Place a TVS diode (e.g., PRTR5V0U2X) on each USB port for ESD protection

Ground Connections

Pin Header
P1-1, P1-2 P1
P1-49, P1-50 P1
P2-1 P2
P2-49 P2

Connect ALL ground pins to the carrier board ground plane. Do not leave any ground pin unconnected.


Reset Circuit

Pin P1-28: RSTI / POR (Power-On Reset)

  • Active LOW input
  • The module includes an on-board reset IC (U18, NL17SZ07XV5T2G) with power-on-reset functionality
  • An external reset button can be connected between P1-28 and GND
  • The module has an internal pull-up; no external pull-up is required
  • Minimum reset pulse width: 1ms recommended

Recovery Jumper

The module includes a recovery jumper (on-board) that forces boot from the boot ROM for firmware recovery. This is accessible on the module PCB itself, not via the headers.


Ethernet Interface Design

On-Board Dual 1 Gbps Ethernet

The module includes two RJ-45 connectors (62F-1319DDD2ZNL) with integrated magnetics, connected via the KSZ9893 three-port Gigabit Ethernet switch. The RGMII bus between the CPU and KSZ9893 is entirely internal to the module.

Switch Operating Modes:

  • Switch mode (default): Both ports share a single MAC address; the KSZ9893 handles layer-2 switching
  • Dual independent mode: Each port has its own MAC address; configured in software

LED Indicators:

Each RJ-45 port has two integral two-lead bicolor (green/yellow) LEDs, driven by the KSZ9893 PHY LED outputs operating in their default tri-color dual-LED mode (the SDK does not reprogram the LED mode). Left/right is as viewed facing the connector opening. Both ports behave identically:

Link State Left LED Right LED
No link Off Off
1000 Mbps link Green Off
100 Mbps link Yellow Off
10 Mbps link Off Green

The LED that is lit for the current link speed blinks with transmit/receive activity. Duplex is not indicated; the KSZ9893 LED modes have no duplex indication.

LED drive circuit: The KSZ9893 LED outputs (LED1_0/LED1_1 for ENET0, LED2_0/LED2_1 for ENET1) are level-shifted to 3.3V by U7/U6 (74AVCH2T45). Each port's left LED is driven differentially by the two shifted outputs through R7/R34 (ENET0) or R6/R33 (ENET1); the right LED is driven by a NAND (U5, TC7WZ00FK) and XOR (U9/U8, 74LVC1G86) decode of the same two signals through R9/R36 (ENET0) or R8/R35 (ENET1), so it lights only when both PHY LED outputs are active (a 10 Mbps link). There are two 165-ohm resistors per LED (one on each leg, each half the normal series value), placed close to the connector to reduce emissions from Ethernet symbol-rate coupling into the LED traces.

Optional 10/100 Ethernet (3rd Interface)

A third Ethernet MAC is available on the header pins using the DISP_B2 pin group on P2. This requires an external PHY on the carrier board.

RMII Pin Mapping (100Mbps):

Signal Pin Pad Alt Function
ENET_TX_EN P2-40 DISP_B2_04 Alt 1
ENET_TX_CLK P2-36 DISP_B2_05 Alt 1
ENET_TDATA0 P2-41 DISP_B2_02 Alt 1
ENET_TDATA1 P2-37 DISP_B2_03 Alt 1
ENET_RX_EN P2-45 DISP_B2_08 Alt 1
ENET_RDATA0 P2-39 DISP_B2_06 Alt 1
ENET_RDATA1 P2-42 DISP_B2_07 Alt 1
ENET_RX_ER P2-35 DISP_B2_09 Alt 1
ENET_MDC P1-11 AD_32 Alt 3
ENET_MDIO P1-13 AD_33 Alt 3
ENET_REF_CLK P2-36 DISP_B2_05 Alt 2 (shared)

External PHY Requirements:

  • Use RMII-capable PHY (e.g., KSZ8081, LAN8720)
  • Provide 50MHz reference clock (from PHY or external oscillator)
  • Place magnetics and RJ-45 connector on the carrier board
  • MDIO/MDC lines are shared with the on-board KSZ9893 – ensure PHY address does not conflict (KSZ9893 uses addresses 1-3)
  • Platform firmware configures ENET reset on LPSR_12 and IRQ on AD_12

IEEE 1588 Precision Time Protocol

1588 event pins are available on the AD pin group:

Signal Pin Pad
ENET_1588_EVENT0_IN P2-5 AD_34
ENET_1588_EVENT1_IN P1-4 AD_00
ENET_1588_EVENT1_OUT P1-20 AD_01
ENET_1588_EVENT2_IN P1-29 AD_08
ENET_1588_EVENT2_OUT P1-12 AD_09
ENET_1588_EVENT3_IN P1-15 AD_10
ENET_1588_EVENT3_OUT P1-14 AD_11

Analog Interface Design

ADC (Analog-to-Digital Converter)

The i.MX RT1171 has two 12-bit ADCs (LPADC1 and LPADC2), sharing a 1.65V reference.

ADC Reference Circuit (on-module):

  • Reference IC: TLVH431AIL5T (U20), 1.65VDC nominal, +/-0.5%
  • Programming resistors: R28 (10K, 0.1%) and R27 (8.45K, 0.1%)
  • Ferrite bead filtering (FB7/FB8, 220R @ 100MHz) on the reference supply

Critical Design Constraint:

  • Default full-scale input: 1.65V (set by the reference)
  • 3.3V signals can be measured directly with no external circuitry: the LPADC's per-channel 30/64 input scaler (CSCALE) extends full scale to 1.65V x 64/30 = 3.52V (see the Software Developer Guide, ADC and DAC chapter)
  • Absolute maximum on any ADC pin: 3.6V (GPIO_AD pad limit) – inputs above this may damage the processor
  • For signals above ~3.5V, use a resistor divider on the carrier board and keep the source impedance seen by the pin at or below 5K

ADC1 Channel Mapping:

Channel Pin Pad Description
CH_A0 P1-27 AD_06 Single-ended
CH_B0 P1-26 AD_07 Diff pair with A0
CH_A1 P1-29 AD_08 Single-ended
CH1B P1-12 AD_09 Diff pair with A1
CH2A P1-15 AD_10 Single-ended
CH2B P1-14 AD_11 Diff pair with 2A
CH3A P1-17 AD_12 Shared with ADC2
CH3B P1-16 AD_13 Shared with ADC2
CH4A P1-19 AD_14 Shared with ADC2
CH4B P1-18 AD_15 Shared with ADC2
CH5A P1-21 AD_16 Single-ended

ADC2 Channel Mapping:

Channel Pin Pad Description
CH0A P2-7 AD_18 Single-ended
CH0B P2-8 AD_19 Diff pair with 0A
CH1A P2-10 AD_20 Single-ended
CH1B P2-11 AD_21 Diff pair with 1A
CH2A P2-12 AD_22 Single-ended
CH2B P2-13 AD_23 Diff pair with 2A
CH3A/3B P1-17/16 AD_12/13 Shared with ADC1
CH4A/4B P1-19/18 AD_14/15 Shared with ADC1
CH5B P2-6 AD_17 Single-ended
CH6A P2-4 AD_24 Single-ended
CH6B P2-3 AD_25 Diff pair with 6A

Layout Recommendations:

  • Route ADC traces away from digital signals and switching power supplies
  • Use a ground guard ring around ADC input traces on the carrier board
  • Keep trace lengths short (< 25mm recommended)
  • Place anti-aliasing RC filter (100R + 100pF) at the carrier board connector

DAC (Digital-to-Analog Converter)

Pin P2-9 (DAC_OUT): 12-bit buffered analog output

On-Module Buffer Circuit:

  • The processor's raw DAC output drives U21 (NCS20166SN2T1G), a low-offset amplifier powered from 3.3V
  • Precision feedback resistors R29 (10K, 0.1%) and R30 (10K, 0.1%) set a non-inverting gain of 2, with 10pF (C106) across the feedback for stability
  • The buffer provides low-impedance output and short-circuit protection (+/-25mA)
  • Buffer offset: +/-1mV max, +/-100uV typical

DAC Specifications:

  • Resolution: 12-bit (4096 steps)
  • Output voltage range at the header: 0 to ~3.3V (raw DAC full scale is the 1.65V ADC_VREFH reference – the RT1170's only DAC reference option – doubled by the x2 buffer)
  • Update rate: 2Msps full-scale, 3.3Msps small-signal
  • Output impedance: Low (buffered)

Note: The DAC output on the header is the BUFFERED signal. The DAC has no dedicated reference pin – it uses the processor's ADC_VREFH pin, the same on-module 1.65V TLVH431 reference that serves the LPADCs.

Analog Comparators (ACMP)

Three comparator modules with 4 inputs each are available:

Comparator Input Pin Pad
ACMP1 IN1 P1-4 AD_00
ACMP1 IN2 P1-20 AD_01
ACMP1 IN3 P1-23 AD_02
ACMP1 IN4 P1-22 AD_03
ACMP2 IN1 P1-25 AD_04
ACMP2 IN2 P1-24 AD_05
ACMP2 IN3 P2-29 AD_26
ACMP2 IN4 P2-38 AD_27
ACMP3 IN1 P2-20 AD_28
ACMP3 IN2 P1-30 AD_29
ACMP3 IN3 P2-26 AD_30
ACMP3 IN4 P2-31 AD_31
ACMP4 IN1 P1-11 AD_32
ACMP4 IN2 P1-13 AD_33
ACMP4 IN3 P2-5 AD_34

Note: ACMP inputs are "No muxing" – they are always connected to the comparator regardless of the pin's ALT function setting. Using a pin for both ACMP input and a digital function simultaneously is possible.


Digital I/O Design

Voltage Domains

Pin Group I/O Voltage Header Pins
GPIO_AD_xx 3.3V P1: 4-27,29-30; P2: 3-8,10-13,20,26,29,31,38
GPIO_SD_B1_xx 3.3V P2: 25,27-28,30,32-33
GPIO_SD_B2_xx 3.3V P1: 5-10 (reserved for on-module flash)
GPIO_DISP_B2_xx 3.3V P2: 21-24,34-37,39-46
GPIO_EMC_B1_xx 3.3V P2: 47-48
GPIO_EMC_B2_xx 3.3V P1: 31
GPIO_LPSR_xx 3.3V P1: 32-47
USB 5V (VBUS), 3.3V (data) P2: 14-19
DAC_OUT 0-1.65V analog P2: 9

All GPIO header pins, including the LPSR pins (P1 pins 32-47), operate at 3.3V on the MODRT1171.

Reset State Defaults

All GPIO pins reset to their GPIO_MUX function (Alt 5) as inputs. Default pull configurations:

Pin Group Default Pull
AD_xx 35K pull-down
SD_B1_xx 50K/35K pull-up
SD_B2_xx Mix of pull-up and pull-down
DISP_B2_xx Mix of high-Z and 35K pull-down
LPSR_xx Varies by pin
EMC_B1/B2 Varies by pin

Drive Strength and Slew Rate

All GPIO pads support configurable:

  • Drive strength: Selectable via pad control registers
  • Slew rate: Fast/slow
  • Open-drain mode: Available on all pads
  • Pull-up/pull-down: Configurable per pin

Communication Interface Routing

UART

The module provides access to 11 LPUART peripherals (LPUART4 is reserved for system debug console).

Recommended Default UART Assignments:

UART TX Pin RX Pin CTS RTS Notes
LPUART7 P1-4 (AD_00) P1-20 (AD_01) P1-23 (AD_02) P1-22 (AD_03) Full modem, 3.3V
LPUART8 P1-23 (AD_02) P1-22 (AD_03) P1-25 (AD_04) P1-24 (AD_05) Shares pins with UART7 flow
LPUART9 P1-10 (SD_B2_0) P1-9 (SD_B2_1) P1-8 (SD_B2_2) P1-5 (SD_B2_3) On SD_B2 pins
LPUART1 P2-4 (AD_24) P2-3 (AD_25) P2-29 (AD_26) P2-38 (AD_27) Full modem, 3.3V
LPUART11 P1-32 (LPSR_08) P1-33 (LPSR_09) P1-34 (LPSR_10) P1-35 (LPSR_11) Full modem
LPUART12 P1-46 (LPSR_06) P1-47 (LPSR_07) P1-45 (LPSR_05) P1-44 (LPSR_04) Full modem
LPUART5 P2-20 (AD_28) P1-30 (AD_29) – – TX/RX only
LPUART3 P2-26 (AD_30) P2-31 (AD_31) – – TX/RX only
LPUART10 P1-11 (AD_32) P1-13 (AD_33) – – TX/RX only
LPUART6 P2-48 (EMC_B1_40) – – – TX only
LPUART2 P2-22 (DISP_10) P2-21 (DISP_11) P2-24 (DISP_12) P2-23 (DISP_13) On Display pins

RS-232/RS-485 Interface:

  • All UARTs output 3.3V CMOS levels
  • For RS-232: Add a level-shifting transceiver (e.g., MAX3232) on the carrier board
  • For RS-485: Add a transceiver (e.g., MAX485) with direction control via a GPIO pin

SPI

Bus SCK SDO (MOSI) SDI (MISO) PCS0 (CS) Domain
LPSPI1 P2-20 (AD_28) P2-26 (AD_30) P2-31 (AD_31) P1-30 (AD_29) 3.3V
LPSPI2 P2-4 (AD_24) P2-29 (AD_26) P2-38 (AD_27) P2-3 (AD_25) 3.3V
LPSPI4 P1-10 (SD_B2_0) P1-8 (SD_B2_2) P1-5 (SD_B2_3) P1-9 (SD_B2_1) 3.3V
LPSPI5 P1-42 (LPSR_02) P1-44 (LPSR_04) P1-45 (LPSR_05) P1-43 (LPSR_03) 3.3V
LPSPI6 P1-34 (LPSR_10) P1-35 (LPSR_11) P1-36 (LPSR_12) P1-33 (LPSR_09) 3.3V

Note: LPSPI3 is used internally for on-module flash and is not available on headers.

I2C

Bus SCL SDA Domain Notes
LPI2C1 P1-11 (AD_32) P1-13 (AD_33) 3.3V Also P1-12/P1-29 option
LPI2C2 P2-7 (AD_18) P2-8 (AD_19) 3.3V
LPI2C3 P2-22 (DISP_10) P2-21 (DISP_11) 3.3V On Display pins
LPI2C4 P2-4 (AD_24) or P2-24 P2-3 (AD_25) or P2-23 3.3V Two routing options
LPI2C5 P1-45 (LPSR_05) P1-44 (LPSR_04) 3.3V
LPI2C6 P1-47 (LPSR_07) P1-46 (LPSR_06) 3.3V

Design Recommendations:

  • Add 2.2K-4.7K pull-up resistors to the appropriate Vcc (3.3V or 1.8V) on the carrier board
  • For long cable runs (> 30cm), consider an I2C bus extender (e.g., P82B96)
  • Maximum bus capacitance: 400pF for standard/fast mode

CAN Bus

Bus TX RX Domain
FLEXCAN1 P1-27 (AD_06) P1-26 (AD_07) 3.3V
FLEXCAN2 P1-4 (AD_00) P1-20 (AD_01) 3.3V
FLEXCAN3 P1-40 (LPSR_00) P1-41 (LPSR_01) 3.3V
  • All three buses support CAN 2.0B and CAN-FD
  • Add a CAN transceiver (e.g., MCP2562FD, TJA1051T) on the carrier board
  • Terminate the CAN bus with 120-ohm resistors at each end

USB

Port VBUS D- D+ Notes
USB OTG1 P2-14 (5V) P2-15 P2-16 HS/FS/LS, integrated PHY
USB OTG2 P2-19 (5V) P2-17 P2-18 HS/FS/LS, integrated PHY

Design Recommendations:

  • Route D+/D- as 90-ohm differential pairs
  • Keep trace lengths matched within 0.5mm
  • Place ESD protection (e.g., PRTR5V0U2X) near the USB connector
  • Add 0.1uF decoupling on VBUS near the connector
  • For host mode, add a current-limiting switch (TPS2051 or similar) controlled by the OTG_PWR pin

SD Card Interface

External SD Card (USDHC1)

USDHC1 is available on P2 for connecting an external SD/SDHC card socket:

Signal Pin Pad Function
CMD P2-27 SD_B1_0 Command line
CLK P2-25 SD_B1_1 Clock (up to 50MHz)
DATA0 P2-28 SD_B1_2 Data bit 0
DATA1 P2-33 SD_B1_3 Data bit 1
DATA2 P2-32 SD_B1_4 Data bit 2
DATA3 P2-30 SD_B1_5 Data bit 3

Design Recommendations:

  • Place the SD card socket as close to the module header as possible
  • Route all signals as 50-ohm controlled impedance
  • Add 33-ohm series resistors on CMD, CLK, and all DATA lines for signal integrity
  • Add 10K pull-up resistors on CMD and DATA lines to 3.3V
  • Include card-detect and write-protect GPIO connections (optional)

On-Module Flash (USDHC2) – RESERVED

P1 pins 5-10 (SD_B2_0 through SD_B2_5) are used for on-module SPI NAND flash storage. These pins must NOT be connected to external SD card sockets or other peripherals. They may still be used as GPIO if the on-module flash is not needed, but this is not recommended.


Display Interface

Parallel LCD (DISP_B2)

16 DISP_B2 pins on P2 (pins 21-24, 34-37, 39-46) can drive a parallel LCD interface:

Signal Pins
LCDIF_DATA[8:23] P2: 44,34,41,37,40,36,39,42,45,35,22,21,24,23,46,43

Note: These pins are shared with the optional 10/100 Ethernet, UART2, CAN1, I2S, and other functions. Only one function can be active per pin at a time.

MIPI DSI/CSI (Optional)

The module schematic includes provisions for MIPI DSI (display) and CSI (camera) connections routed from the CPU through FFC connectors. These are intended for the 1172/1176 graphics-capable SKU variants and are not populated on the standard MODRT1171-100IR.


Layout Guidelines

Carrier Board Connector Placement

  • Module headers are on 0.1" (2.54mm) pitch
  • Minimum clearance: 10mm around each RJ-45 connector for cable access
  • Allow 5mm clearance below the module for airflow

Signal Integrity

  • USB differential pairs: Route as 90-ohm differential, length-matched within 0.5mm
  • SD card signals: Route as 50-ohm, length-matched within 5mm
  • High-speed digital (SPI, I2S): Keep trace lengths under 100mm
  • Analog (ADC inputs): Route away from switching supplies; use ground guard traces

Thermal Considerations

  • The module dissipates 1.35-2.6W depending on Ethernet configuration
  • Ensure adequate airflow across the module surface
  • For enclosed designs at +85C ambient, consider a small heatsink on the processor
  • The mounting hole can be used for a thermal standoff

EMI/EMC

  • Connect all module ground pins to a solid ground plane
  • Place ferrite beads (e.g., BLM18PG221SN1D) on power supply inputs to the module
  • Keep USB and Ethernet traces short and well-shielded
  • For conducted emissions compliance, add common-mode chokes on Ethernet connections external to the module (on-module Ethernet already includes magnetics)

Appendix A: Pin-to-Peripheral Quick Reference

Pins Reserved by Module (Do Not Use)

Pins Function Notes
P1: 5-10 USDHC2 (on-module flash) SD_B2 group, Note 2 in pinout
Internal LPSPI3 Boot/app flash SPI bus
Internal RGMII CPU-to-KSZ9893 Ethernet switch bus
Internal SDRAM bus 32-bit SDRAM interface

Pins Available for General GPIO

Any pin not in the reserved list above can be configured as GPIO. Total available GPIO: up to 88 pins (including analog-capable pins used as digital).


MODRT1171-100IR | PRELIMINARY | Schematic Rev 1.6, 2/18/2026 *NetBurner, Inc. | www.netburner.com | sales.nosp@m.@net.nosp@m.burne.nosp@m.r.co.nosp@m.m | 1-800-695-6828*